For mounting heating Combi, you must first determine the location of combi on balcony, kitchen, bath, of course would be better if the combi bet outdoors. Combi can be used both in the kitchen to wash dishes, shower in the bath, and for heating in winter. After you define the place is done, assembling lines.
Combi has 4 inputs.The first blue line, shown in the picture, we use for filling combi, it is cold water.It heats up and is used in the bath, the kitchen.The first red line it is hot water.These lines are slightly larger in diameter than the line of radiators
...
Read more »
|
Setting the toilet by using silikon. It is applied to the surface of the toilet bowl and on the surface of ceramic tiles. After applying silikon, put the toilet at the right place for us, and leave to dry.
Next, you need to bridge the holes toilet with sewage line by siphoning.
Then, we check to see if there was any leaks, flush the toilet.&
...
Read more »
|
Scheme sewer lines, defined primarily in the bath and in the kitchen.
These pipes should be fastened tightly to each other as possible, so that there was no leaks. Take into account the correct location of the gangway sewage, the line sinks in the bath and kitchen, also take into account the water flow of the washing machine. All required bends are carried out by means of couplings, knees and tees.Installation of sewers, you have to make a line of inclination, to allow water to drain.
...
Read more »
|
First of all, you need to create a circuit of water pipes.
After that, we will need iron for installation of pipes and scissors for cutting the required length.
We also need corners, couplings and tees.
...
Read more »
|
First, you need to make the installation of sewer pipes, and take into account all the pipes that will be under concrete. And only then begin to work.
For this we need the 4 pegs. To hammer the pegs into the floor at each corner, and cut around the thread.Then using the water level draw a dash on pegs and align the thread on dash.
...
Read more »
|
This requires wooden blocks. They need to be fixed with plugs and screws.
 
But first, you need to make marks on the wall, with using the water level.After marking, fasten the first block.And on the other part of the wall, fasten a second block.Further, stretch the thread on the beam.And follow the level of the thread , fasten the other wooden blocks .
...
Read more »
|
If the room is concrete, we need wooden blocks. Fasten them using the plugs and screws.
But first, you need to make marks on the wall, with using the water level.After marking, fasten the first block.And on the other part of the wall, fasten a second block.Further, stretch the thread on the beam.And follow the level of the thread , fasten the other wooden blocks .
...
Read more »
|
Laying laminate flooring is very easy procedure. We need to lay special flooring for laying laminate.
After starting from the edge of the wall mount laminate. Laminate attached special latch. For work, we need a rubber hammer, a saw.In necessary places you can cut with using a saw our laminate
...
Read more »
|
Installation room doors need to remove trim, lay door on the floor, and fix the trim on the door with nails, and leave a gap in order to avoid friction door to frame.
Here you need to leave room for the door lock, given the small gap between the door and trim. Then remove the so-called box, and set it to the doorway in the correct vertical position.
...
Read more »
|
If the door is in China, it will be fixed with anchor bolts. If the door of any other production, will need welding machine. Door frame with the door is installed in a doorway, and are using level measured the correct vertical position of the door frame. You can do without the level. To do this, open the door, and if any of its open position, it should not be movable. If there is any movement in the direction of closing, or vice versa in the direction of opening the door, corrects the curvature of the door frame.Once the door is in the correct, upright position, fasten it with anchor bolts or by means of fittings bars driven into the wall.
...
Read more »
|
After laying the tiles on the floor, should be laying the tiles on the wall. This is done in order to tile the wall, sitting down on a tile lying on the floor. Tile smear with a special solution, then smear the wall, and a light touch on the tiles to, thicken to the wall.
You first need to attach profeli whith using a spirit level
...
Read more »
|
On the concrete surface, which has a small bias, you need put the tiles with a special solution. Where necessary, we make a cutout on the tile, using the special cutter.
Solution should be put on the concrete surface and on the tiles.
Further put the tiles on the concrete surface, and easy to press it from the top side.
...
Read more »
|
|
